This page will be updated throughout the process of the build as it will reflect the choices I’ve made in terms of parts/equipment.
Empennage Kit – additions
- NACA Vents (direct link – Vans Aircraft)
- Static Kit (direct link – Vans Aircraft)
- Static Ports Deluxe (direct link – Vans Aircraft)
Avionics
All avionics (up until now) from SteinAir (direct link to homepage)
- GDU 460, GPS Touch Display Only (10″) (2 pcs)
- Garmin GDU460 Connector/Install Kit (2 pcs)
- Garmin GDU Aux RS232 Connector Kit
- Garmin 26X Internal Mounted GPS Antenna
- G3X LRU Kit with GSU-25, GMU-22, GTP-59 and Config Module
- Garmin GMU22 Connector/Install Kit
- Garmin GSU25 Connector/Install Kit
- Garmin GEA-24B EIS Engine Monitor Module
- Garmin GEA24 Connector/Install Kit
- Sensor Kit, 6 Cylinder Lyc/Cont, GPT
- Sub-Assy, Pressure Sensor, GPT 75G
- Garmin GMC507 Autopilot Control Panel
- Garmin GMC-507 Connector/Install Kit
- Garmin GSA28 Autopilot Servo (3 pcs)
- Garmin GSA28 Servo Connector (2 pcs)
- Garmin GSA28 Right Angle Connector Kit for Yaw Damper Servo
- Garmin GSA 28 YAW DAMPER INSTALL KIT, RV10
- Garmin G3X Pitch Servo Install Kit, RV10
- Garmin G3X Roll Servo Install Kit, RV7/8/10
- Garmin GAD29, ARINC 429 Adapter for G3X
- Garmin GAD29 Connector/Install Kit
- Garmin GNX 375,+ GA 35
- Garmin GTR 205X, VHF Comm Radio
- Garmin GTR 205XR, Remote VHF Comm Radio
- GMA-245 Standard Audio Panel
- Kit, Standard, G5 for Experimental/LSA Aircraft, w/ LPM and battery
- Garmin HEATED Pitot tube, with AOA, regulated (14V only)
- Mounting Kit, GAP 26 Pitot, Adjustable
- Pitot & Static Tubing and Port kit
- GHA 15 Height Advisor, includes connector kit
- VP-X Pro system
- TCW IBBS 3amp-hour Li-fe-PO4 back-up battery system
- TCW IBBS 6amp-hour Li-fe-PO4 back-up battery system
- Aithre Shield EX 3.0, Carbon Monoxide Detector (Remote)
- CI-122 VHF BENT Whip COMM Antenna (2 pcs)
- CI-105 Blade transponder / ADS-B antenna
- Stereo Headset Jack (4 pcs)
- Microphone Jack (4 pcs)
- Fiber Washer Set (8 pcs)
- Bose Headset Install Connector Kit (4 pcs)
- Aluminum eye ball air Vent, 1.25″ outlet, 2″ mounting hole. Black anodized finish (2 pcs)
Harnesses
All harnesses (up until now) from SteinAir (direct link to homepage)
- Garmin G3X system wiring harness – includes wiring for LRU’s and engine probes/sensors,
EGT/CHT leads - Garmin A/P wiring harness. Includes servo leads.
- ARINC Converter ModuleHarness
- Garmin GNX-375 Harness
- Comm radio harness
- Audio Panel Harness
- Garmin G5/Backup EFIS wire harness
- Garmin GHA-15 Height Advisor Wiring Harness
- VP-X Pro Wiring Harness
- TCW d-sub harness for backup battery system
- CO DETECTOR HARNESS
- ELT wiring harness
PANEL
- Panel Design and cut (link – SteinAir)
- RV10 Carbon Fiber/FG Panel Paint and Prep. (link – SteinAir)
- Laser engraving (link – SteinAir)